##
## tinyproxy.conf -- tinyproxy daemon configuration file
##
## This example tinyproxy.conf file contains example settings
## with explanations in comments. For decriptions of all
## parameters, see the tinproxy.conf(5) manual page.
##

#
# User/Group: This allows you to set the user and group that will be
# used for tinyproxy after the initial binding to the port has been done
# as the root user. Either the user or group name or the UID or GID
# number may be used.
#
User tinyproxy
Group tinyproxy

#
# Port: Specify the port which tinyproxy will listen on.  Please note
# that should you choose to run on a port lower than 1024 you will need
# to start tinyproxy using root.
#
Port 8888

#
# Timeout: The maximum number of seconds of inactivity a connection is
# allowed to have before it is closed by tinyproxy.
#
Timeout 60


#
# DefaultErrorFile: The HTML file that gets sent if there is no
# HTML file defined with an ErrorFile keyword for the HTTP error
# that has occured.
#
DefaultErrorFile "/usr/share/tinyproxy/default.html"

#
# StatFile: The HTML file that gets sent when a request is made
# for the stathost.  If this file doesn't exist a basic page is
# hardcoded in tinyproxy.
#
StatFile "/usr/share/tinyproxy/stats.html"

#
# LogFile: Allows you to specify the location where information should
# be logged to.  If you would prefer to log to syslog, then disable this
# and enable the Syslog directive.  These directives are mutually
# exclusive.
#
LogFile "/var/log/tinyproxy/tinyproxy.log"

#
# Syslog: Tell tinyproxy to use syslog instead of a logfile.  This
# option must not be enabled if the Logfile directive is being used.
# These two directives are mutually exclusive.
#
#Syslog On

#
# LogLevel:
#
# Set the logging level. Allowed settings are:
# Critical  (least verbose)
# Error
# Warning
# Notice
# Connect   (to log connections without Info's noise)
# Info    (most verbose)
#
# The LogLevel logs from the set level and above. For example, if the
# LogLevel was set to Warning, then all log messages from Warning to
# Critical would be output, but Notice and below would be suppressed.
#
LogLevel Notice


XTinyproxy No


#
# MaxClients: This is the absolute highest number of threads which will
# be created. In other words, only MaxClients number of clients can be
# connected at the same time.
#
MaxClients 10

MinSpareServers 2
MaxSpareServers 10

#
# StartServers: The number of servers to start initially.
#
StartServers 5

#
# MaxRequestsPerChild: The number of connections a thread will handle
# before it is killed. In practise this should be set to 0, which
# disables thread reaping. If you do notice problems with memory
# leakage, then set this to something like 10000.
#
MaxRequestsPerChild 10000

#
# Allow: Customization of authorization controls. If there are any
# access control keywords then the default action is to DENY. Otherwise,
# the default action is ALLOW.
#
# The order of the controls are important. All incoming connections are
# tested against the controls based on order.
#
#Allow 127.0.0.1


#
# DisableViaHeader: When this is set to yes, Tinyproxy does NOT add
# the Via header to the requests. This virtually puts Tinyproxy into
# stealth mode. Note that RFC 2616 requires proxies to set the Via
# header, so by enabling this option, you break compliance.
# Don't disable the Via header unless you know what you are doing...
#
DisableViaHeader Yes

#
# Filter: This allows you to specify the location of the filter file.
#
Filter "/etc/tinyproxy/filter.conf"

#
# FilterURLs: Filter based on URLs rather than domains.
#
#FilterURLs On

#
# FilterExtended: Use POSIX Extended regular expressions rather than
# basic.
#
#FilterExtended On

#
# FilterCaseSensitive: Use case sensitive regular expressions.
#
#FilterCaseSensitive On

#
# FilterDefaultDeny: Change the default policy of the filtering system.
# If this directive is commented out, or is set to "No" then the default
# policy is to allow everything which is not specifically denied by the
# filter file.
#
# However, by setting this directive to "Yes" the default policy becomes
# to deny everything which is _not_ specifically allowed by the filter
# file.
#
FilterDefaultDeny Yes

#
# Anonymous: If an Anonymous keyword is present, then anonymous proxying
# is enabled.  The headers listed are allowed through, while all others
# are denied. If no Anonymous keyword is present, then all headers are
# allowed through.  You must include quotes around the headers.
#
# Most sites require cookies to be enabled for them to work correctly, so
# you will need to allow Cookies through if you access those sites.
#
#Anonymous "Host"
#Anonymous "Authorization"
#Anonymous "Cookie"

#
# ConnectPort: This is a list of ports allowed by tinyproxy when the
# CONNECT method is used.  To disable the CONNECT method altogether, set
# the value to 0.  If no ConnectPort line is found, all ports are
# allowed (which is not very secure.)
#
# The following two ports are used by SSL.
#
ConnectPort 443
ConnectPort 563